Vörulýsing
- Einnig fáanlegur hvítur
- Hægt að veðurverja með Rain Kit Upgrade
- Rigging aukahlutir og fleira í boði
With an operating range of 35Hz-150Hz ± 3dB, it houses dual 18” long-excursion (460mm)/4” (100mm) voice coil drivers with water-resistant cones and triple roll surrounds. The design of the 18” drivers maximises output while minimising power compression and distortion, and the eight reflex ports have a large frontal area to reduce turbulent air noise at very high levels. With a prodigious maximum SPL capability of 143dB peak at 1 metre, the SXP218 is the ideal subwoofer for touring sound reinforcement, theatre and portable live sound applications — as well as premium installations — that require low frequency augmentation with low distortion at very high output levels.
A self-powered system, the SXP218 incorporates a Class D amplifier, DSP and Dante™ digital audio networking — simplifying set-up, enhancing control and eliminating amplifier racks. The onboard amplifier delivers a total of 4000W peak output to the drivers, and its switched-mode power supply auto-ranges to global mains voltages from 100 to 240V 50/60Hz. DSP functions — including parametric EQ, delay, muting, gain and preset selection — can be controlled over Ethernet from a PC or Windows® tablet via intuitive VU-NET™ proprietary software.
For simple set-ups, ‘plug-and-play’ presets for operation with the CDD-LIVE 8, CDD-LIVE 12 or CDD-LIVE 15 — as well as a user-defined preset — can be selected on the rear panel, instead of using computer control. Additional presets provide the appropriate settings for the rear-facing subwoofer in a cardioid pair.
As an alternative to its analogue inputs, the SXP218 is Dante enabled for digital audio distribution and control over a single CAT5 cable to maintain audio quality however long the cable run.
The enclosure is constructed from multi-laminate plywood with a durable polyurea coating and equipped with a perforated Zintec grille, four grab handles, skids and M10 flying inserts. SXP218 also features an M20 pole mount insert for added versatility in deployment.
The product is supplied as standard without cabinet wheels, but they are available as an accessory. By adding the input board cover accessory, the subwoofer is fully weather resistant and suitable for permanent outdoor usage.
Specification
| Acoustics | |
| TYPE | Dual-driver, direct radiating powered subwoofer |
| FREQUENCY RESPONSE | 35Hz – 150Hz ±3dB, -10dB @ 30Hz |
| DRIVER | 2x 18” (460mm)/4” (100mm) voice coil, long excursion, ferrite magnet, waterproof cone |
| INPUT SENSITIVITY | -30dBu for 100dB SPL |
| MAXIMUM SPL | 140dB continuous / 143dB peak |
| DISPERSION | Omnidirectional / or Cardioid (paired) |
| CROSSOVER | Active Presets for CDD Live 8, 12 & 15 mono-pole or cardioid (paired) |
| Module Audio input | |
| CONNECTORS | Female XLR input, male XLR link output, Dante Audio Neutrik® Ethercon |
| ANALOGUE INPUT IMPEDANCE | 20 kΩ balanced to ground |
| MAXIMUM ANALOGUE INPUT LEVEL | 24.6 Vpp (+21dBu), over voltage protected |
| INTERNAL PROCESSING | Multi-channel DSP, programmable via TCP/IP using VU-Net software PEQ/shelving filters Up to 48dB/Oct LPF Up to 200mS input delay Pre-set selection via rear panel switch |
| Network | |
| CONNECTORS | 2 x Neutrik® Ethercon RJ45 |
| PROTOCOL | TCP/IP and UDP/IP |
| Amplifier Module | |
| TYPE | Two 2 channel switch-mode, class D, Bridged Tied Load |
| PEAK OUTPUT POWER | 4000W |
| AVERAGE EFFICIENCY | 89% |
| COOLING | External fan |
| MAXIMUM AMBIENT TEMPERATURE | 40°C (104°F) for full output |
| Power Supply | |
| TYPE | Switch mode, fixed frequency with PFC |
| AC INPUT OPERATING RANGE | 85 – 265V ~ AC, 50 – 60Hz |
| POWER FACTOR | > 0.98 |
| NOMINAL POWER CONSUMPTION | 250W |
| MAINS CONNECTOR | Neutrik® Powercon True1 |
| Mechanical | |
| ENCLOSURE | Extensively braced multi-laminate birch plywood. |
| FINISH | Durable Polyurea Coating |
| PROTECTIVE GRILLE | Black perforated Zintec |
| FITTINGS |
|
| IP RATING | IP24 factory option available |
| DIMENSIONS | (W) 1085mm x (H) 537mm x (D) 792mm (920mm including castors) (W) 42.72in x (H) 21.13in x (D) 31.16in (36.20in including castors) |
| WEIGHT | 101.5kg (224lbs) w/o castors 105kg (231lbs) with castors |
